FreeBSD SSH配置详解

首先vi编辑/etc/inetd.conf,去掉ssh前的#，保存退出
编辑/etc/rc.conf
最后加入:sshd_enable="yes"即可
激活sshd服务：
techo#/etc/rc.d/sshd start
用下面命令检查服务是否启动，在22端口应该有监听。
#netstat -an ## check port number 22
最后
vi /etc/ssh/sshd_config,
下面是我的配置文件：(/etc/ssh/sshd_config)
####################################################
# $OpenBSD: sshd_config,v 1.72 2005/07/25 11:59:40 markus Exp $
# $FreeBSD: src/crypto/openssh/sshd_config,v 1.42.2.1 2005/09/11 16:50:35 des Exp $
# This is the sshd server system-wide configuration file. See
# sshd_config(5) for more information.
# This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin
# The strategy used for options in the default sshd_config shipped with
# OpenSSH is to specify options with their default value where
# possible, but leave them commented. Uncommented options change a
# default value.
# Note that some of FreeBSD's defaults differ from OpenBSD's, and
# FreeBSD has a few additional options.
#VersionAddendum FreeBSD-20050903
#Port 22
#Protocol 2
#AddressFamily any
#ListenAddress 10.1.10.196
#ListenAddress ::
# HostKey for protocol version 1
#HostKey /etc/ssh/ssh_host_key
# HostKeys for protocol version 2
#HostKey /etc/ssh/ssh_host_dsa_key
# Lifetime and size of ephemeral version 1 server key
#KeyRegenerationInterval 1h
#ServerKeyBits 768
# Logging
# obsoletes QuietMode and FascistLogging
#SyslogFacility AUTH
#LogLevel INFO
# Authentication:
#LoginGraceTime 2m
#PermitRootLogin no
#StrictModes yes
#MaxAuthTries 6
#RSAAuthentication yes
#PubkeyAuthentication yes
#AuthorizedKey .ssh/authorized_keys
# For this to work you will also need host keys in /etc/ssh/ssh_known_hosts
#RhostsRSAAuthentication no
# similar for protocol version 2
#HostbasedAuthentication no
# Change to yes if you don't trust ~/.ssh/known_hosts for
# RhostsRSAAuthentication and HostbasedAuthentication
#IgnoreUserKnownHosts no
# Don't read the user's ~/.rhosts and ~/.shosts files
#IgnoreRhosts yes
# Change to yes to enable built-in password authentication.
PasswordAuthentication yes
#PermitEmptyPasswords no
# Change to no to disable PAM authentication
#ChallengeResponseAuthentication yes
# Kerberos options
#KerberosAuthentication no
#KerberosOrLocalPasswd yes
#KerberosTicketCleanup yes
#KerberosGetAFSToken no
# GSSAPI options
#GSSAPIAuthentication no
#GSSAPICleanupCredentials yes
# Set this to 'no' to disable PAM authentication, account processing,
# and session processing. If this is enabled, PAM authentication will
# be allowed through the ChallengeResponseAuthentication mechanism.
# Depending on your PAM configuration, this may bypass the setting of

标签：

版权申明：本站文章部分自网络，如有侵权，请联系：west999com@outlook.com
特别注意：本站所有转载文章言论不代表本站观点，本站所提供的摄影照片，插画，设计作品，如需使用，请与原作者联系，版权归原作者所有